Isishwankathelo seProjekthi
1. Inkqubo yeMveliso
Iiseti ezingama-600 ngosuku (i-117/118 bearing pedestral)
2. Iimfuno zomgca wokucubungula:
1) Iziko loomatshini le-NC elifanelekileyo kumgca wemveliso ozenzekelayo;
2) I-hydraulic frock clamp;
3) Isixhobo sokulayisha nokuvala ngokuzenzekelayo kunye nesixhobo sokuhambisa;
4) Itekhnoloji yokucubungula iyonke kunye nexesha lomjikelo wokucubungula;
Uyilo lweMigca yeMveliso
Uyilo lweMigca yeMveliso
Intshayelelo yeZenzo zeRobhothi:
1. Beka ngesandla iingobozi ezifakwe ngomatshini nezibekwe kwitafile yokulayisha (Iitafile zokulayisha No. 1 kunye No. 2) uze ucinezele iqhosha ukuqinisekisa;
2. Irobhothi isiya kwitreyi yetafile yokulayisha yeNombolo 1, ivula inkqubo yokubona, ibambe kwaye ihambise iiCandelo A kunye no-B ngokulandelelanayo ukuya kwisikhululo sokujonga esijikelezayo ukuze ilinde umyalelo wokulayisha;
3. Umyalelo wokulayisha uthunyelwa sisikhululo sokuqaphela esijikelezayo. Irobhothi ibeka iqhekeza elinguNombolo 1 kwindawo yokuma kwetafile yokujika. Jikelezisa itafile yokujika uze uqalise inkqubo yokuqaphela ejikelezileyo, umisele indawo ye-angular, umise itafile yokujika uze ugqibezele ukuqaphela kweqhekeza elinguNombolo 1;
4. Inkqubo yokuqaphela i-angular ithumela umyalelo wokungangeni, kwaye irobhothi ithatha iqhekeza eliyiNombolo 1 ize ifake iqhekeza eliyiNombolo 2 ukuze ikwazi ukuchongwa. I-turntable iyajikeleza kwaye inkqubo yokuqaphela i-angular iqala ukumisela indawo ye-angular. I-turntable iyama kwaye ukuchongwa kwe-angular kweqhekeza eliyiNombolo 2 kugqityiwe, kwaye umyalelo wokungangeni uthunyelwa;
5. Irobhothi ifumana umyalelo wokuvala i-lathe ethe nkqo enguNombolo 1, itshintshela kwindawo yokulayisha kunye nokuvala i-lathe ethe nkqo enguNombolo 1 yokuvala i-lathe yezinto zokwakha kunye nokulayisha. Emva kokuba isenzo sigqityiwe, umjikelo womatshini we-lathe ethe nkqo uqala;
6. Irobhothi ithatha iimveliso ezigqityiweyo nge-lathe ethe nkqo yeNombolo 1 ize izibeke kwindawo yeNombolo 1 kwitafile yokuqengqeleka kwe-workpiece;
7. Irobhothi ifumana umyalelo wokuvala i-blanking we-lathe ethe nkqo enguNombolo 2, itshintshela kwindawo yokulayisha kunye nokuvala i-blanking ye-lathe ethe nkqo enguNombolo 2 yokuvala i-blanking kunye nokulayisha izinto, kwaye emva koko isenzo sigqityiwe, kwaye umjikelo wokucubungula we-lathe ethe nkqo uqala;
8. Irobhothi ithatha iimveliso ezigqityiweyo nge-lathe ethe nkqo yeNombolo 2 ize izibeke kwindawo yeNombolo 2 kwitafile yokuqengqeleka kwe-workpiece;
9. Irobhothi ilinde umyalelo wokuvala i-blanking ovela kwi-machining ethe nkqo;
10. Umatshini othe nkqo uthumela umyalelo wokuvala intsimbi, kwaye irobhothi ihambela kwindawo yokulayisha kunye nokuvala intsimbi yematshini ethe nkqo, ibambe kwaye ihambise izixhobo zokusebenza zezikhululo zeNombolo 1 kunye neNombolo 2 ngokulandelelana kwitreyi yokuvala intsimbi, kwaye ibeke izixhobo zokusebenza kwitreyi ngokulandelelana; Irobhothi ihambela kwitafile yokuqengqeleka ukuze ibambe kwaye ithumele iziqwenga zeNombolo 1 kunye neNombolo 2 kwiindawo zokulayisha kunye nokuvala intsimbi yemashini ethe nkqo, kwaye ibeke izixhobo zokusebenza zeNombolo 1 kunye neNombolo 2 kwindawo yokubeka yezikhululo zeNombolo 1 kunye neNombolo 2 ze-hydraulic clamp ngokulandelelana ukuze igqibezele ukulayisha intsimbi yemashini ethe nkqo. Irobhothi ihambela ngaphandle komgama wokhuseleko wemishini ethe nkqo kwaye iqalise umjikelo omnye wokucubungula;
11. Irobhothi ifudukela kwitreyi yokulayisha yeNombolo 1 kwaye ilungiselela ukuqalisa inkqubo yomjikelo wesibini;
Inkcazo:
1. Irobhothi ithatha iziqwenga ezili-16 (umaleko omnye) kwitreyi yokulayisha. Irobhothi iza kuthatha indawo yetong yokufunxa indebe ize ibeke ipleyiti yokwahlulahlula kwingobozi yokugcina yexeshana;
2. Irobhothi ipakisha iziqwenga ezili-16 (umaleko omnye) kwitreyi engenanto. Irobhothi kufuneka itshintshe itoti yokufunxa kube kanye, ize ibeke ipleyiti yokufunxa phezu komphezulu wokufunxa weendawo ezivela kwingobozi yokugcina yexeshana;
3. Ngokwexesha lokuhlolwa, qiniseka ukuba irobhothi ibeka inxalenye kwitafile yokuvavanya ngesandla;
| 1 | Ishedyuli yomjikelo wokwenziwa kwemishini | ||||||||||||||
| 2 | Umthengi | Izinto zokusebenza | QT450-10-GB/T1348 | Imodeli yesixhobo somatshini | Inombolo yoLondolozo lweMbali | ||||||||||
| 3 | Igama lemveliso | 117 Isihlalo sebheyari | Inombolo yomzobo | DZ90129320117 | Umhla wokulungiselela | 2020.01.04 | Ilingiselelwe ngu | ||||||||
| 4 | Inyathelo lenkqubo | Inombolo yemela | umxholo womatshini | Igama leSixhobo | Ububanzi bokusika | Isantya sokusika | Isantya sokujikeleza | Ukutya ngokujikeleza ngakunye | Ukutya ngesixhobo somatshini | Inani leenqunqa | Inkqubo nganye | Ixesha loomatshini | Ixesha Lokungasebenzi | Ixesha lokujikeleza eline-axis ezine | Ixesha lokutshintsha isixhobo |
| 5 | Hayi. | Hayi. | IiDesoriptions | Izixhobo | D mm | n | R pm | mm/Rev | mm/Umn | Amaxesha | mm | Isekh | Isekh | Isekh | |
| 6 |  | ||||||||||||||
| 7 | 1 | T01 | Umphezulu womngxuma wokufaka umngxuma | Ububanzi bomsiki wokugaya obunobuso obungama-40 | 40.00 | 180 | 1433 | 1.00 | 1433 | 8 | 40.0 | 13.40 | 8 | 4 | |
| 8 | Drill DIA 17 imingxunya yokufaka | I-DIA 17 COMBINED DRILL | 17.00 | 100 | 1873 | 0.25 | 468 | 8 | 32.0 | 32.80 | 8 | 4 | |||
| 9 | T03 | I-DIA 17 hole back chamfering | Umsiki we-chamfering obuyela umva | 16.00 | 150 | 2986 | 0.30 | 896 | 8 | 30.0 | 16.08 | 16 | 4 | ||
| 10 | Inkcazo: | Ixesha lokusika: | 62 | Isibini | Ixesha lokubopha ngezinto ezisetyenziswayo kunye nokulayisha kunye nokuvala izinto: | 30.00 | Isibini | ||||||||
| 11 | Ixesha lokuncedisa: | 44 | Isibini | Iiyure zomsebenzi zoomatshini ezipheleleyo: | 136.27 | Isibini | |||||||||
| 1 | Ishedyuli yomjikelo wokwenziwa kwemishini | |||||||||||||||||
| 2 | Umthengi | Izinto zokusebenza | QT450-10-GB/T1348 | Imodeli yesixhobo somatshini | Inombolo yoLondolozo lweMbali | |||||||||||||
| 3 | Igama lemveliso | 118 Isihlalo sebheyari | Inombolo yomzobo | DZ90129320118 | Umhla wokulungiselela | 2020.01.04 | Ilingiselelwe ngu | |||||||||||
| 4 | Inyathelo lenkqubo | Inombolo yemela | umxholo womatshini | Igama leSixhobo | Ububanzi bokusika | Isantya sokusika | Isantya sokujikeleza | Ukutya ngokujikeleza ngakunye | ukondla ngesixhobo somatshini | Inani leenqunqa | Inkqubo nganye | Ixesha loomatshini | Ixesha Lokungasebenzi | Ixesha lokujikeleza eline-axis ezine | Ixesha lokutshintsha isixhobo | |||
| 5 | Hayi. | Hayi. | IiDesoriptions | Izixhobo | D mm | n | R pm | mm/Rev | mm/Umn | Amaxesha | mm | Isekh | Isekh | Isekh | ||||
| 6 | 
| |||||||||||||||||
| 7 | 1 | T01 | Umphezulu womngxuma wokufaka umngxuma | Ububanzi bomsiki wokugaya obunobuso obungama-40 | 40.00 | 180 | 1433 | 1.00 | 1433 | 8 | 40.0 | 13.40 | 8 | 4 | ||||
| 8 | T02 | Drill DIA 17 imingxunya yokufaka | I-DIA 17 COMBINED DRILL | 17.00 | 100 | 1873 | 0.25 | 468 | 8 | 32.0 | 32.80 | 8 | 4 | |||||
| 9 | T03 | I-DIA 17 hole back chamfering | Umsiki we-chamfering obuyela umva | 16.00 | 150 | 2986 | 0.30 | 896 | 8 | 30.0 | 16.08 | 16 | 4 | |||||
| 10 | Inkcazo: | Ixesha lokusika: | 62 | Isibini | Ixesha lokubopha ngezinto ezisetyenziswayo kunye nokulayisha kunye nokuvala izinto: | 30.00 | Isibini | |||||||||||
| 11 | Ixesha lokuncedisa: | 44 | Isibini | Iiyure zomsebenzi zoomatshini ezipheleleyo: | 136.27 | Isibini | ||||||||||||
| 12 | ||||||||||||||||||
Indawo yokugubungela umgca wemveliso
Intshayelelo yezinto eziphambili ezisebenzayo zomgca wemveliso
Intshayelelo yenkqubo yokulayisha kunye nokuvala isithuba
Izixhobo zokugcina umgca wemveliso ozenzekelayo kolu cwangciso zezi: Itreyi ebekwe ndawonye (ubuninzi beziqwenga eziza kupakishwa kwitreyi nganye kuya kuxoxiswana ngazo nomthengi), kwaye indawo yokusebenza kwitreyi iya kugqitywa emva kokubonelela ngomzobo we-3D we-workpiece engenanto okanye into yokwenyani.
1. Abasebenzi bapakisha iindawo ezicociweyo kwitreyi yezinto (njengoko kubonisiwe kumfanekiso) baze baziphakamise ngefolokhwe bazibeke kwindawo ebekiweyo;
2. Emva kokutshintsha itreyi yeforklift, cofa iqhosha ngesandla ukuqinisekisa;
3. Irobhothi ibamba into yokusebenza ukuze yenze umsebenzi wokulayisha;
Intshayelelo yeRobot Travel Axis
Isakhiwo senziwe yirobhothi edibeneyo, i-servo motor drive kunye ne-pinion kunye ne-rack drive, ukuze irobhothi ikwazi ukwenza intshukumo ethe tye isiya phambili nangasemva. Ifezekisa umsebenzi werobhothi enye ekhonza izixhobo zoomatshini ezininzi kunye neendawo zokusebenzela ezibambayo kwizikhululo ezahlukeneyo kwaye inokunyusa ukugubungela kokusebenza kweerobhothi ezidibeneyo;
Umzila wokuhamba ufaka isiseko esidityanisiweyo ngemibhobho yentsimbi kwaye uqhutywa yi-servo motor, i-pinion kunye ne-rack drive, ukwandisa ukugquma kokusebenza kwerobhothi edibeneyo kunye nokuphucula ngempumelelo izinga lokusetyenziswa kwerobhothi; Umzila wokuhamba ufakwe emhlabeni;
Irobhothi yaseChenxuan:SDCX-RB500
| Idatha esisiseko | |
| Uhlobo | I-SDCX-RB500 |
| Inani lee-axes | 6 |
| Ukhuseleko oluphezulu | 2101mm |
| Ukuphindaphinda kwepozi (ISO 9283) | ± 0.05mm |
| Ubunzima | 553kg |
| Ulwahlulo lokhuseleko lwerobhothi | Uvavanyo loKhuseleko, IP65 / IP67isihlakala esisemgceni(IEC 60529) |
| Indawo yokufakela | Isilingi, i-engile yokuthambekela evumelekileyo ≤ 0º |
| Ukugqitywa komphezulu, umsebenzi wokupenda | Isakhelo sesiseko: mnyama (RAL 9005) |
| Ubushushu obugciniwe | |
| Umsebenzi | 283 K ukuya kwi-328 K (0 °C ukuya kwi-+55 °C) |
| Ukugcina kunye nokuthuthwa | 233 K ukuya kwi-333 K (-40 °C ukuya kwi-+60 °C) |
Ngoluhlu olubanzi lweendawo zokuhamba ngasemva nasezantsi kwerobhothi, ekubeni yimodeli enokuxhonywa ngokuphakamisa isilingi. Ngenxa yokuba ububanzi obusecaleni berobhothi buncitshisiwe, kunokwenzeka ukuba ifakwe kufutshane nerobhothi ekufutshane, i-clamp, okanye i-workpiece. Ukuhamba ngesantya esiphezulu ukusuka kwindawo yokulinda ukuya kwindawo yokusebenza kunye nokubeka indawo ngokukhawuleza ngexesha lokuhamba komgama omfutshane.
Indlela yokulayisha irobhothi ekrelekrele kunye neyokuvula i-blanking tong
Indlela yokuqhekeza ipleyiti yerobhothi
Inkcazo:
1. Xa sijonga iimpawu zale nxalenye, sisebenzisa indlela yokuxhasa yangaphandle enezipikili ezintathu ukulayisha nokukhupha izinto, nto leyo enokwenza ukuba iindawo ezikwisixhobo somatshini zijike ngokukhawuleza;
2. Le ndlela ixhotyiswe nge-sensor yokubona indawo kunye ne-sensor yoxinzelelo ukuze kubonwe ukuba imeko yokubopha kunye noxinzelelo lwamalungu ziqhelekile na;
3. Le ndlela ixhotyiswe nge-pressurizer, kwaye i-workpiece ayizukuwa ngexesha elifutshane xa umbane ucima kwaye igesi inqanyulwe yi-air circuit ephambili;
4. Isixhobo sokutshintsha isandla siyasetyenziswa. Indlela yokutshintsha itong ingagqibezela ngokukhawuleza ukubethelwa kwezinto ezahlukeneyo.
Intshayelelo yesixhobo sokutshintsha iiTong
Isixhobo sokutshintsha iitong esichanekileyo sisetyenziselwa ukutshintsha ngokukhawuleza iitong zerobhothi, iziphelo zezixhobo, kunye nezinye izixhobo ezisebenza ngekhompyutha. Ukunciphisa ixesha lokungasebenzi kwemveliso kunye nokwandisa ukuguquguquka kwerobhothi, oku kuboniswe ngolu hlobo:
1. Vula kwaye uqinise uxinzelelo lomoya;
2. Iimodyuli ezahlukeneyo zamandla, ulwelo kunye negesi zingasetyenziswa;
3. Uqwalaselo oluqhelekileyo lunokunxibelelana ngokukhawuleza nomthombo womoya;
4. Iiarhente zeinshorensi ezikhethekileyo zinokuthintela umngcipheko wokucinywa kwegesi ngengozi;
5. Akukho mandla okusabela kwentwasahlobo; 6. Isebenza kwintsimi yokuzenzekela;
Intshayelelo kwiKhamera yeMibono-yeShishini
1. Ikhamera isebenzisa iitships zeCCD kunye neCMDS ezikumgangatho ophezulu, ezineempawu zomlinganiselo wesisombululo esiphezulu, uvakalelo oluphezulu, umlinganiselo wesignali ukuya kwi-frequency ephezulu, uluhlu olubanzi lwe-dynamic, umgangatho ogqwesileyo womfanekiso kunye nokukwazi ukubuyisela umbala kwiklasi yokuqala;
2. Ikhamera ye-Area array ineendlela ezimbini zokudlulisela idatha: i-GIGabit Ethernet (GigE) interface kunye ne-USB3.0 interface;
3. Ikhamera inesakhiwo esincinci, inkangeleko encinci, ilula kwaye ifakiwe. Isantya esiphezulu sokudlulisa, amandla okumelana nokuphazamiseka, imveliso ezinzileyo yomfanekiso osemgangathweni ophezulu; Isebenza ekufundeni ikhowudi, ekufumaneni iziphene, ekuqaphelweni kwe-DCR kunye neepateni; Ikhamera yombala inamandla okubuyisela umbala, ifanelekile kwiimeko ezifuna ukuqatshelwa kombala ophezulu;
Intshayelelo yeNkqubo yokuQondwa kweAngular Automatic
Intshayelelo yoMsebenzi
1. Irobhothi ibopha izinto zokusebenza kwiingobozi zokulayisha ize izithumele kwindawo yokuma ye-turntable;
2. I-Turntable ijikeleza phantsi kwe-drive ye-servo motor;
3. Inkqubo yokubona (ikhamera yemizi-mveliso) isebenza ukuchonga indawo ye-engile, kwaye i-turntable iyama ukufumanisa indawo ye-engile efunekayo;
4. Irobhothi ikhupha into yokusebenza ize ifake enye into ukuze ibonakale ngekona;
Intshayelelo kwiTheyibhile yokuGqibela yoMsebenzi
Isitishi sokuqengqeleka:
1. Irobhothi ithatha isixhobo somsebenzi ize isibeke kwindawo yokuma kwitafile yokuqengqeleka (isikhululo sasekhohlo kumfanekiso);
2. Irobhothi ibamba i-workpiece ukusuka apha ngasentla ukuze ikwazi ukujika i-workpiece;
Itafile yokubeka iRobot Tong
Intshayelelo yoMsebenzi
1. Emva kokuba umaleko ngamnye weendawo ulayishiwe, ipleyiti yokwahlulahlula enezitena kufuneka ibekwe kwingobozi yokugcina yexeshana yeepleyiti zokwahlulahlula;
2. Irobhothi ingatshintshwa ngokukhawuleza ngezibambo zekomityi yokufunxa ngesixhobo sokutshintsha izibambo kwaye isuse iipleyiti zokwahlulahlula;
3. Emva kokuba iipleyiti zokwahlulahlula zibekwe kakuhle, susa i-suction cup tong uze ufake i-pneumatic tong ukuze uqhubeke nokulayisha kunye nezinto zokuvala;
Ingobozi yokugcina okwethutyana iipleyiti zokwahlulahlula
Intshayelelo yoMsebenzi
1. Ingobozi yexeshana yeepleyiti zokwahlulahlula iyilwe kwaye icwangcisiwe njengoko iipleyiti zokwahlulahlula zokulayisha zirhoxiswa kuqala kwaye iipleyiti zokwahlulahlula zokuvala zisetyenziswa kamva;
2. Iipleyiti zokwahlulahlula umthwalo zifakwa ngesandla kwaye azilunganga kakuhle. Emva kokuba ipleyiti yokwahlulahlula ifakwe kwingobozi yokugcina ixeshana, irobhothi ingayikhupha iyibeke kakuhle;
Itheyibhile yesampulu esetyenziswa ngesandla
Inkcazo:
1. Misela amaxesha ahlukeneyo okusebenzisa iisampulu ezingacwangciswanga ngesandla kwiinqanaba ezahlukeneyo zemveliso, ezinokujonga ngempumelelo ukusebenza kokulinganisa kwi-intanethi;
2. Imiyalelo Yokusetyenziswa: I-manipulator iza kubeka isixhobo somsebenzi kwindawo ebekwe kwitafile yesampulu ngokwexesha elibekwe ngesandla, ize iqalise ngesibane esibomvu. Umhloli uza kucinezela iqhosha lokuthutha isixhobo somsebenzi ukuya kwindawo yokhuseleko engaphandle kokhuseleko, akhuphe isixhobo somsebenzi ukuze silinganiswe aze asigcine ngokwahlukileyo emva kokulinganisa;
Izinto ezikhuselayo
Yenziwe ngeprofayili ye-aluminiyam ekhaphukhaphu (40×40)+mesh (50×50), kwaye isikrini sokuchukumisa kunye neqhosha lokumisa elingxamisekileyo zinokudityaniswa kwizinto ezikhuselayo, zidibanise ukhuseleko kunye nobuhle.
Intshayelelo ye-OP20 Hydraulic Fixture
Imiyalelo Yokucubungula:
1. Thatha imbobo yangaphakathi ye-φ165 njengomngxuma osisiseko, thatha i-D datum njengeplani esisiseko, kwaye uthathe i-arc yangaphandle ye-boss yemingxuma emibini yokufaka njengomda we-angular;
2. Lawula isenzo sokukhulula nokucinezela kwepleyiti yokucinezela ngomyalelo wesixhobo somatshini M ukuze ugqibezele ukucutshungulwa kweplani ephezulu yebhosi yomngxuma wokuqhobosha, umngxuma wokuqhobosha ongu-8-φ17 kunye neziphelo zombini zomngxuma;
3. Le nto inemisebenzi yokumisa, ukubopha ngokuzenzekelayo, ukufumanisa ukuqina komoya, ukukhulula ngokuzenzekelayo, ukukhupha ngokuzenzekelayo, ukufutha iitshiphusi ngokuzenzekelayo kunye nokucoca ngokuzenzekelayo i-datum plane yokumisa;
Iimfuneko zeZixhobo zoMgca weMveliso
1. I-clamp yezixhobo zomgca wemveliso inemisebenzi yokuzibopha nokuzikhulula ngokuzenzekelayo, kwaye iyazifezekisa imisebenzi yokuzibopha nokuzikhulula ngokuzenzekelayo phantsi kolawulo lwemiqondiso yenkqubo ye-manipulator ukuze isebenzisane nesenzo sokulayisha nokuzikhulula;
2. Indawo ye-skylight okanye imodyuli yomnyango ozenzekelayo kufuneka igcinelwe ipleyiti yesinyithi yezixhobo zomgca wemveliso, ukuze ihambelane nesignali yokulawula umbane kunye nonxibelelwano lwe-manipulator yenkampani yethu;
3. Izixhobo zomgca wemveliso zinonxibelelwano ne-manipulator ngendlela yoqhagamshelo lwesixhobo sokudibanisa umthwalo onzima (okanye iplagi yendiza);
4. Izixhobo zomgca wemveliso zinendawo yangaphakathi (yokuphazamiseka) enkulu kunoluhlu olukhuselekileyo lwesenzo somhlathi we-manipulator;
5. Izixhobo zomgca wemveliso maziqinisekise ukuba akukho zitshiphusi zentsimbi eziseleyo kumphezulu wokubeka i-clamp. Ukuba kuyimfuneko, ukuvuthela umoya kuya kwandiswa ukuze kucocwe (i-chuck mayijikeleze xa kucocwa);
6. Izixhobo zomgca wemveliso zinokwaphuka kakuhle kweetshiphusi. Ukuba kuyimfuneko, isixhobo sokuncedisa sokukwaphuka kweetshiphusi esinoxinzelelo oluphezulu senkampani yethu siya kongezwa;
7. Xa izixhobo zomgca wemveliso zifuna ukumisa ngokuchanekileyo i-spindle yesixhobo somatshini, yongeza lo msebenzi kwaye unikeze imiqondiso yombane ehambelanayo;
Intshayelelo ye-Vertical Lathe VTC-W9035
I-VTC-W9035 NC vertical lathe ifanelekile ekusetyenzisweni kwezixhobo ezijikelezayo ezifana nee-gear blanks, ii-flanges kunye nee-shells ezimile ngendlela ekhethekileyo, ifanelekile ngakumbi ekujikeni ngokuchanekileyo, okonga abasebenzi kunye nokusebenza kakuhle kweendawo ezifana neediski, ii-hubs, ii-brake discs, ii-pump bodies, ii-valve bodies kunye nee-shells. Isixhobo somatshini sineenzuzo zokuqina okuhle, ukuchaneka okuphezulu, izinga elikhulu lokususa isinyithi ngexesha ngalinye, ukugcinwa ngokuchanekileyo okuhle, ukuthembeka okuphezulu, ukugcinwa lula, njl.njl. kunye noluhlu olubanzi lwezicelo. Imveliso yemigca, ukusebenza kakuhle kunye neendleko eziphantsi.
| Uhlobo lomzekelo | I-VTC-W9035 |
| Ububanzi obukhulu bokujika bomzimba webhedi | Φ900 mm |
| Ububanzi obukhulu bokujika kwipleyiti yokutyibiliza | Φ590 mm |
| Ububanzi obukhulu bokujika kwento yokusebenza | Φ850 mm |
| Ubude obukhulu bokujika kwento yokusebenza | 700 mm |
| Uluhlu lwesantya se-spindle | 20-900 r/min |
| Inkqubo | I-FANUC 0i - TF |
| Ukubetha okuphezulu kwe-axis ye-X/Z | 600/800 mm |
| Isantya esikhawulezayo sokuhamba kwe-axis ye-X/Z | 20/20 m/ngomzuzu |
| Ubude, ububanzi kunye nokuphakama kwesixhobo somatshini | 3550*2200*3950 mm |
| Iiprojekthi | Iyunithi | Ipharamitha | |
| Uluhlu lokucubungula | Uhambo lwe-X axis | mm | 1100 |
| Uhambo lwe-X axis | mm | 610 | |
| Uhambo lwe-X axis | mm | 610 | |
| Umgama ukusuka kwimpumlo yespindle ukuya kwibhentshi yokusebenza | mm | 150～760 | |
| Ibhentshi yokusebenzela | Ubungakanani bebhentshi yokusebenza | mm | 1200×600 |
| Umthwalo ophezulu webhentshi yomsebenzi | kg | 1000 | |
| I-T-groove (ubungakanani×ubungakanani×isithuba) | mm | 18×5×100 | |
| Ukondla | Isantya sokutya esikhawulezayo se-axis ye-X/Y/Z | m/ngomzuzu | 36/36/24 |
| I-Spindle | Imo yokuqhuba | Uhlobo lwebhanti | |
| I-spindle taper | BT40 | ||
| Isantya esiphezulu sokusebenza | r/min | 8000 | |
| Amandla (Alinganiswe/Aphezulu) | KW | 11/18.5 | |
| I-Torque (Ilinganiswe/Iphezulu) | N·m | 52.5/118 | |
| Ukuchaneka | Ukuchaneka kokubeka i-axis ye-X/Y/Z (i-half closed loop) | mm | 0.008 (ubude obupheleleyo) |
| Ukuchaneka kokuphindaphinda kwe-axis ye-X/Y/Z (i-half closed loop) | mm | 0.005 (ubude obupheleleyo) | |
| Imagazini yezixhobo | Uhlobo | Idiski | |
| Ubungakanani besixhobo semagazini | 24 | ||
| Ubungakanani obukhulu besixhobo(Ububanzi besixhobo obupheleleyo/ububanzi besixhobo esikufutshane esingenanto/ubude) | mm | Φ78/Φ150/ 300 | |
| Ubunzima obukhulu besixhobo | kg | 8 | |
| Ezininzi | Uxinzelelo lomoya | I-MPa | 0.65 |
| Umthamo wamandla | I-KVA | 25 | |
| Ubungakanani besixhobo somatshini ngokubanzi (ubude×ububanzi×ukuphakama) | mm | 2900×2800×3200 | |
| Ubunzima besixhobo somatshini | kg | 7000 | |
